1102 silver lake road cary il 60013 phone fax 800-981-0363 847-639-1508 e-mail web cps@coilcraft.com www.coilcraft-cps.com ? ? coilcraft, inc. 2010 these parts are preproduction products for electrical evaluation only. specification subject to change without notice. outgassing compliant chip inductors ae235raa 0402 chip inductors document ae198-1 revised 06/15/10 ab cd max max max ref e f g h i j 0.047 0.025 0.026 0.010 0.020 0.009 0.022 0.026 0.014 0.018 1,19 0,64 0,66 0,25 0,51 0,23 0,56 0,66 0,36 0,46 a b overall c d j f f g h e terminal terminal wraparound: approx 0.007/0,18 both ends i i suggested land pattern core material ceramic terminations tin-lead (63/37) over s ilver-platinum-glass frit ambient temperature ?55c to +125c with i max current, +125c to +155c with derated current storage temperature component: ?55c to +155c. packaging: ?55c to +80c resistance to soldering heat max three 40 second reflows at +260c, parts cooled to room temperature between cycles temperature coefficient of inductance (tcl) +25 to +155 ppm/c moisture sensitivity level (msl) 1 (unlimited floor life at <30c / 85% relative humidity) enhanced crush-resistant p ackaging 2000 per 7 reel paper tape: 8 mm wide, 0.68 mm thick, 2 mm pocket spacing -40 -55 -20 0 20 40 60 80 100 160 140 120 ambient temperature (c) percent of rated rms i 120 110 100 90 80 70 60 50 40 30 20 10 0 25c current derating typical q vs frequency 0 60 50 40 30 20 10 70 80 90 100 110 120 q factor 1 10 100 1000 10000 frequency (mhz) 12 nh 19 nh 5.6 nh 27 nh 1 nh 56 nh typical l vs frequency 0 10 20 30 40 50 60 1 10 100 1000 10000 frequency (mhz) inductance (nh) 27 nh 56 nh 19 nh 12 nh 5.6 nh 1 nh exceptionally high q factors outstanding self-resonant frequency tight inductance tolerance high temperature materials allow operation in ambient temperatures up to 155c. passes nasa low outgassing specifications leach-resistant base metalization with tin-lead (sn-pb) terminations ensures the best possible board adhesion all dimensions are without solder applied to the terminations. for maximum dimensions with solder, add 0.006 inches / 0,152 mm.
1102 silver lake road cary il 60013 phone fax 800-981-0363 847-639-1508 e-mail web cps@coilcraft.com www.coilcraft-cps.com ? ? coilcraft, inc. 2010 these parts are preproduction products for electrical evaluation only. specification subject to change without notice. ae235raa series (0402) document ae198-2 revised 06/15/10 0402 chip inductors inductance 2 percent 900 mhz 1.7 ghz srf min 5 dcr max 6 i max part number 1 (nh) tolerance q min 3 l typ q typ 4 l typ q typ 4 (ghz) (ohms) (ma) ae235raa1n0jsz 1.0 5 20 1.02 77 1.02 69 >5.00 0.045 1360 ae235raa1n2jsz 1.2 5 12 1.17 28 1.17 38 >5.00 0.090 740 ae235raa1n8jsz 1.8 5 20 1.78 54 1.78 75 >5.00 0.070 1040 ae235raa1n9jsz 1.9 5 20 1.72 68 1.74 82 >5.00 0.070 1040 ae235raa2n0_sz 2.0 5,2 20 1.93 54 1.93 75 >5.00 0.070 1040 ae235raa2n2_sz 2.2 5,2 20 2.19 59 2.23 100 >5.00 0.070 960 ae235raa2n4_sz 2.4 5,2 20 2.24 51 2.27 68 >5.00 0.068 790 ae235raa2n7_sz 2.7 5,2 16 2.58 42 2.60 61 >5.00 0.120 640 ae235raa3n3_sz 3.3 5,2 20 3.10 65 3.12 87 >5.00 0.066 840 ae235raa3n6_sz 3.6 5,2 20 3.56 45 3.62 71 >5.00 0.066 840 ae235raa3n9_sz 3.9 5,2 20 3.89 50 4.00 75 >5.00 0.066 840 ae235raa4n3_sz 4.3 5,2 20 4.19 47 4.30 71 >5.00 0.091 700 ae235raa4n7_sz 4.7 5,2 20 4.55 48 4.68 68 4.77 0.130 640 ae235raa5n1_sz 5.1 5,2 20 5.15 56 5.25 82 4.80 0.083 800 ae235raa5n6_sz 5.6 5,2 20 5.16 54 5.28 81 4.80 0.083 760 ae235raa6n2_sz 6.2 5,2 20 6.16 52 6.37 76 4.80 0.083 760 ae235raa6n8_sz 6.8 5,2 20 6.56 63 6.93 78 4.80 0.083 680 ae235raa7n5_sz 7.5 5,2 22 7.91 60 8.22 88 4.80 0.104 680 ae235raa8n2_sz 8.2 5,2 22 8.50 57 8.85 84 4.40 0.104 680 ae235raa8n7_sz 8.7 5,2 20 8.78 54 9.21 73 3.80 0.195 480 ae235raa9n0_sz 9.0 5,2 22 9.07 62 9.53 78 4.66 0.100 680 ae235raa9n5_sz 9.5 5,2 20 9.42 54 9.98 69 3.48 0.195 480 ae235raa10n_sz 10.0 5,2 21 9.8 50 10.10 67 3.68 0.195 480 ae235raa11n_sz 11.0 5,2 24 10.7 52 11.20 78 3.48 0.120 640 ae235raa12n_sz 12.0 5,2 24 11.9 53 12.70 71 3.60 0.120 640 ae235raa13n_sz 13.0 5,2 20 13.4 51 14.63 57 3.28 0.210 440 ae235raa15n_sz 15.0 5,2 22 14.6 55 15.50 77 3.10 0.172 560 ae235raa16n_sz 16.0 5,2 23 16.6 46 18.86 47 3.05 0.220 560 ae235raa18n_sz 18.0 5,2 24 18.3 57 20.28 62 2.68 0.230 420 ae235raa19n_sz 19.0 5,2 24 19.1 50 21.10 67 3.00 0.202 480 ae235raa20n_sz 20.0 5,2 24 20.7 52 23.66 53 2.90 0.250 420 ae235raa22n_sz 22.0 5,2 24 23.2 53 26.75 53 2.80 0.300 400 ae235raa23n_sz 23.0 5,2 24 23.8 49 26.90 64 2.72 0.300 400 ae235raa24n_sz 24.0 5,2 24 25.1 51 29.50 50 2.60 0.300 400 ae235raa27n_sz 27.0 5,2 24 28.7 49 33.50 63 2.48 0.298 400 ae235raa30n_sz 30.0 5,2 24 31.1 46 38.50 39 2.35 0.410 400 ae235raa33n_sz 33.0 5,2 20 34.9 31 41.74 32 2.30 0.300 400 ae235raa36n_sz 36.0 5,2 24 39.5 44 48.40 53 2.20 0.440 320 ae235raa39n_sz 39.0 5,2 24 41.7 47 50.23 45 2.10 0.550 200 ae235raa40n_sz 40.0 5,2 24 39.0 44 47.40 33 2.24 0.440 320 ae235raa43n_sz 43.0 5,2 22 45.8 46 61.55 34 2.03 0.810 100 ae235raa47n_sz 47.0 5,2 20 50.0 38 ? ? 2.10 0.830 150 ae235raa51n_sz 51.0 5,2 19 56.6 40 ? ? 1.75 0.820 100 ae235raa56n_sz 56.0 5,2 22 62.8 42 ? ? 1.76 0.966 100 ae235raa68n_sz 68.0 5,2 22 78.2 36 ? ? 1.62 1.120 100 ae235raa82n_sz 82.0 5,2 25 ? ? ? ? 1.26 1.550 100 ae235raar10_sz 100 5,2 25 ? ? ? ? 1.16 2.000 50 ae235raar12_sz 120 5,2 22 ? ? ? ? 1.20 1.780 50 1. when ordering, please specify tolerance and testing codes: ae235raar10 g s z tolerance: g =2% j = 5% testing: z = cots h = screening per coilcraft cp-sa-10001 n = screening per coilcraft cp-sa-10003 c = custom screening (please specify when ordering) 2. inductance measured at 250 mhz using a coilcraft smd-f test fixture and coilcraft-provided correlation pieces with an agilent/hp 4286 impedance analyzer. 3. q measured at 250 mhz using an agilent/hp 4291a with an agilent/ hp 16193 test fixture 4. q measured using an agilent/hp 4291a with an agilent/hp 16193 test fixture. 5. srf measured using an agilent/hp 8753d network analyzer and a coilcraft smd-d test fixture. 6. dcr measured on a micro-ohmmeter. 7. electrical specifications at 25c. refer to doc 362 ?soldering surface mount components? before soldering.
|
